- 1. [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: Ross Piercey <ross-piercey@home.com>
- Date: Thu, 16 Sep 1999 06:23:11 -0600
- When I was removing the driver side door one of the bolts on the bottom hinge snapped off. I used WD40 on it but, ho well you know how it goes. I was wondering what is the best way to get the broken
- /html/oletrucks/1999-09/msg00444.html (7,826 bytes)
- 2. Re: [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: Wayne Osborne <wcosborne@inetnow.net>
- Date: Thu, 16 Sep 1999 10:34:17 -0400
- Been there done that Ross...I used a dremmel tool to cut a slot in the broken bolt then was able to use a screw driver to remove it. With the dremmel you can get a fairly deep cut for the slot. If ya
- /html/oletrucks/1999-09/msg00448.html (8,884 bytes)
- 3. Re: [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: Tim Holbrook <t.holbrook@morehead-st.edu>
- Date: Thu, 16 Sep 1999 10:44:57 -0400 (EDT)
- Ever used those bolt removers where you first drill a small hole in the center of the broken bolt and then the remover has reverse threads so that it turns the bolt out as it tightens into the bolt.
- /html/oletrucks/1999-09/msg00449.html (8,753 bytes)
- 4. Re: [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: Bob Fischer <bfischer@utm.net>
- Date: Thu, 16 Sep 1999 07:44:52 -0700
- Hi Ross, I just recently removed the drivers side door on our AD and I went very gingerly with lots of WD40, and eventually got all 6 out, but it sure feels bad when they tighten up. I don't know if
- /html/oletrucks/1999-09/msg00451.html (9,010 bytes)
- 5. Re: [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: jls <jls@sessio.com>
- Date: Thu, 16 Sep 1999 10:43:00 -0700 (PDT)
- I had a similar experience with one bolt on each of the dors on my '54. I used a number of techniques and was able to get one out clean. The other I had to drill and retap. I used heat from a blow to
- /html/oletrucks/1999-09/msg00469.html (8,428 bytes)
- 6. Re: [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: "David" <David@gardener.com>
- Date: Thu, 16 Sep 1999 17:47:12 -0500
- What about welding a stub on the broken bolt? David Edwards 1953 3100 5 Window oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
- /html/oletrucks/1999-09/msg00475.html (8,329 bytes)
- 7. Re: [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: Advdesign1@aol.com
- Date: Thu, 16 Sep 1999 19:59:52 EDT
- << I used a dremmel tool to cut a slot in the broken bolt then was able to use a screw driver to remove it. >> If you cut a slot screw it in till it drops out the back. Threads on back side of hinge
- /html/oletrucks/1999-09/msg00476.html (7,792 bytes)
- 8. Re: [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: "Keith" <kvdurand@mail.esc4.com>
- Date: Thu, 16 Sep 1999 20:55:55 -0700
- I tried this on a seat bolt that was stuck in the floor. MIG welded a nut to it, and although it will rock back and forth about 45 degrees, nothing will make it come out all the way. The nuts keep tw
- /html/oletrucks/1999-09/msg00480.html (9,087 bytes)
- 9. [oletrucks] Broken Door Hinge Bolt (score: 1)
- Author: Ross Piercey <ross-piercey@home.com>
- Date: Fri, 17 Sep 1999 06:25:20 -0600
- Thanks to everyone for the great tips on how to get this bolt out. First i'll try cutting a slot in the end for a flat screwdriver, then i'll put some heat to it and while it's still hot i'll crank t
- /html/oletrucks/1999-09/msg00490.html (7,761 bytes)
This search system is powered by
Namazu